Road Kerb Details - Civil Scoops

Kerbs In Roads

• The top of the kerbs should be 100 mm above the road surface. With the pavement, the kerb is laid on a concrete bed of at least 100 mm thickness.
• At least 150 mm to provide lateral support the kerbing should be provided. To the concrete level, kerbs can be tapped.
• the longitudinal drainage system this type of kerb is beneficial and the height of this type of kerbs is 70 to 80 mm.
• Commonly most straight kerbs are 915 mm in length but sometimes the small type of kerbs are manufactured as per requirement.
• In transportation engineering, the radius kerbs are generally 780 mm in length.
• In the beginning, natural stone was used as kerbs stone but nowadays this has largely been replaced with precast concrete.
  For severe emergency vehicles, they can climb and be parked on footpath or shoulder.
• For the longitudinal drainage system, this type of curb is beneficial and the height of this type of kerbs is 70 to 80 mm, and this type
  of kerbs known as mountable kerbs.

Shape of Kerbs

• Kerb is also a vertical or nearly vertical face is called a barrier or non-mountable curb.
• To discharge the motor vehicle drivers from leaving the roadway.
• In towns or cities, the square or nearly square kerbs are used.
• At low speed, the motor vehicle is moved on a sloped kerb.
• On the suburban thoroughfares, slope face kerb is majorly used.
• In a certain place like California to achieve a standardized design and construction at low cost using 610 mm gutter that balanced
  the initial and maintenance cost.
• The high containment kerbs are used in great Britain in a location with pedestrian, fuel station pumps, and other areas where they
  need greater protection from vehicle traffic.
  To reducing the coast there are also used to eliminate the need for driveway cuts, kerbs, and aprons.
• To the driveways, the rounded kerbs are mostly used where the continuously along suburban residential streets are many driveways and sidewalk has a grassy from the street.
• This type of kerns is generally used in flat roads or areas.

Materials of Kerbs in Roads

• Kerbs are constructed with many materials like asphalt, the stone of masonry blocks, etc but now a days Portland cement is
  mostly used for construct the kerbs.
• The type of materials depends on the nature and purpose of the road.
• Provide a highly visible barrier at the edge of the road surface Portland concrete kerb with asphalt concrete road is used.
• The concrete kerb is constructed by setting form by hand, filling them, letting them set up, and removing the forms.
• If the requirements of concrete kerb are large then to full fill the requirement slip machine is used.
• By the paving machine, the asphalt kerb is made.
• The asphalt kerb is cheaper than the concrete kerb if it is made at the same time when the road is paved.
• But the asphalt kerb is less durable than the concrete kerb.
• By the granite, the stone kerbs are made. It is more durable and has more resistant power than the other kerbs.
• For aesthetic reasons, it is generally used.
• The disadvantage of the granite kerbs is when they cut a tire sidewall if it is the rough face.
• These kerbs are vertical or angle to create a mountable kerb.

Kerb Height

• When an engineer designs a road kerb then specify the reveal or lip. The height of the section is known as a reveal that is visible
  above the road surface.
• The range of typical road kerbs is 4 to 8 inches or 100 to 200 mm.
• For the accommodate automobile design, the recommendations have been used 4/12 better.
• Because the steeper batter tends to interface with body trim and lower door edge while kerb face in excess 152 mm in height.
• To improve the kerb stability most kerbs are extended down into the ground below the pavement surface.
• 16-inch should be the total height of the kerb including the buried portion.

What Is Kerb Stone?

The kerbs stone is generally used in the edge of the carriageway or footpath. By the granite, the stone kerbs are made. It is more durable and has more resistant power than the other kerbs.

For aesthetic reasons, it is generally used. It has some disadvantage of the granite kerbs is when they cut a tire sidewall if it is the rough face. These kerbs are vertical or angle to create a mountable kerb.

Materials of Kerb Stone

Many different types of cement are used in kerbs stone construction.

• That’s are ordinary Portland cement, rapid herding cement, low heat Portland cement, Portland slag cement, Portland pozzolana cement, and super sulfated cement, etc.
• There are all grades of aggregate are used. But the aggregate impact value, crushing value, and abrasion value should not be exceeded the following requirements.
• Nowadays an alternative coarse aggregate blast furnace slag is used in construction in stone kerbs. That has more sulfate resistance power from kerbs stone.
• And this type of kerbs shall not absorb more than 10 percent of the water of its mass. The grade concrete that is used in stone kerb construction shall not be less than M20 grade and high strength is required.

Types of Kerbs

There are four types of kerbs:-

• Low or Mountable Kerbs.
• Low-Speed Barrier or Urban Parking Kerbs.
• High-Speed Barrier Kerbs.
• Submerged Kerbs.

1. Low or Mountable Kerbs

The low or mountable kerbs are also known as class I kerbs. The main principle of the kerbs is to control traffic to stay within its lane. To provide facilitates the driver to enter the area of the shoulder with less difficulty the height of this form of kerb is low.

For the longitudinal drainage system, this type of kerb is beneficial and the height of this type of kerbs is 70 to 80 mm.

2. Low-Speed Barrier or Urban Parking Kerbs

The low-speed barrier or urban parking kerbs is also known as class II kerbs. To the footpath to prevent encroachment of slow speed or parking vehicles. For severe emergency vehicles, they can climb and be parked on footpath or shoulder.

To avoid the scraping of tires the height of this type 0f kerbs is 150 to 200 mm.

3. High-Speed Barrier Kerbs

The high-speed barrier kerbs are also known as class III kerb. In the bridges, mountains, or where the path is critical there the high-speed barrier kerbs are used. The height of this type of kerbs is lies between 230 to 450 mm or more.

4. Submerged Kerbs

The submerged kerb is also known as class IV kerb. This type of kerbs is also provided in rural roads at pavement edges between edges and shoulders. To provide lateral stability to the granular base course and flexible pavements.

In the form of standing bricks or concrete blocks, it is provided.

Road Kerb

Road kerbs are the most essential things in the transportation system and it provides the following purposes-

• Between the footpath and pavement, it acts as a boundary wall.
• The road kerb prevents the vehicle from parking beside the road.
• To the pavement, the kerbs provide structural support.
• To overcome the slipping risk of the vehicles it helps.
• To reduce the number of accident its help.
• For drainage purposes, it is also used.
• To provide lateral stability to the granular base course and flexible pavements
• This type of kerbs is also provided in rural roads at pavement edges between edges and shoulders.

Road Kerb Details

• Kerbs is an edge where a raised sidewalk or road median meets a Street or other roads.
• Kerbs are constructed with many materials like asphalt, the stone of masonry blocks, etc but now a days Portland cement is
  mostly used for construct the kerbs.
• The asphalt kerb is cheaper than the concrete kerb if it is made at the same time when the road is paved.
• There have many numbers kerbs that are categorized by shape, high, material, and where the kerb is combined with a gutter.
• From the pavement, most kerb is constructed separately and at the joint, the gutter is formed between the roadway and the curb.
• Generally, most straight kerbs are 915 mm in length but sometimes the small type of kerbs are manufactured as per requirement.
• In the beginning, natural stone was used as kerbs stone but nowadays this has largely been replaced with precast concrete.

FAQ

Kerbs

A kerbs is the edge where a raised sidewalk or road median/central reservation meets a street or other roadway.

See also

What Is Transportation Engineering | Major Disciplines of Transportation Engineering | What Do Transportation Engineers Do

Types of Kerbs

Here, the different types of kerbs in highways are as follows.

1. Low or Mountable Kerbs.
2. Low-Speed Barrier or Urban Parking Kerb.
3. High-Speed Barrier Kerbs.
4. Submerged Kerbs.

Kerbs in Roads

The meaning of kerbs or curbs is a barrier or boundary. But in highway engineering, it indicates the boundary between the pavement and shoulder or sometimes island or footpath or car parking space. kerbs are generally constructed of cut stone or cement concrete slabs.

Kerb Height

For most purposes, the top of the kerb should be 100 mm above the road surface.

Kerb Stone

Stone Kerbs Marble, For Landscaping ₹ 700/Piece. Gray Stone Kerbs Stones, For Landscaping ₹ 500/Piece. Outdoor Stone Kerbs, For Pavement ₹ 700/Piece. Mint Kerb Stone, for Flooring, for Landscaping. ₹ 150/ PieceGet Latest Price.

What Is Kerb Used For?

Their purpose is to prevent traffic leaving the carriageway and are used on dangerous curves, for pedestrian islands, and to protect footpaths or equipment.

Kerbs In Roads

The kerb (British English) or curb (American English) is the raised edge of the road where the footpath or median is separated from the street or roadway.

Functions of Kerbs

The main functions of kerb are to provide structural support to the edges of the roads and channel rainwater away [4–13]. By providing effective drainage, it can reduce cracking and other surface and structural defects and effectively increase the service life of a pavement.